Description：

TIEAKO^®“ 闪电侠”  is  a  two-part fast-setting epoxy adhesive which bonds to a wide variety of substrates

such as wood, metal, ceramics and some plastics and composites. It cures rapidly at room temperature  to

give handling strength in approximately 5 minutes. This product is ideal for general purpose bonding. It is

typically used for small component assembly and is suitable for applications that require a clear bond line.

Recommended Substrates:

Glass, Metals, Circuit Boards, Fiber Optics and many Plastics.

Features：

1.Clear Color

2.Adhesion to a wide variety of substrates

3.Full cure at room temperature

4.Easy to apply Fast setting

5.100% Solids

Physical Properties of Uncured Adhesive:

Typical Uncured Properties	Part A	Part B
Chemical composition	Epoxy Resin	Amine Hardener
Color	Colourless	Amber
Viscosity @ 25°C	12,000-18,000mPa.s(cP)	15,000-30,000mPa.s(cP)
Specific gravity	1.12	1.06

Typical Curing Properties:

Mix ratio by volume	1:1
Maximum gap fill	2 mm
Usable / pot life @25°C	3-4mins
Handling time @25°C	5-8mins
Working strength @25°C	30-60mins
Full cure @25°C	24 hours

Typical Performance of Cured Adhesive:

Shear strength (mild steel)*(ISO4587)	12-18 N/mm²(1700 - 2600psi)
Peel strength (aluminium)(ISO4578)	5-20N/25mm (1-4 PIW)
Hardness (ISO868)	75-80 Shore D
Elongation at break (ISO37)	<5%
Glass transition temperature Tg	70-80°C
Dielectric strength	15-25 kv/ mm
Thermal conductivity	0.22 W/(m.K)
Dielectric Strength,ASTM D149,V/mil	1080
Dielectric Constant,MIL 1-16923.K 1kHz	3.88

Handling:

Mixing: This product requires mixing two components together just prior to application. Complete mixing is

necessary. The temperature  of  the  separate components prior to mixing is not critical, but they  should be

close to room temperature.

Application:

Please remove the packing cap and install the mixing tube. Gently push the push rod so that the AB

component can be fully mixed in the mixing tube and evenly extruded and applied to the parts to be

bonded. Products  that  have  been  used  can  be stored in  connection with mixing pipes. To reuse,

remove and discard the old mixing pipe, install a new mixing pipe can be reused.

Bonding surfaces should be clean and dry. Once the adhesive is applied, the bonded parts should be held in

contact  until  the part  has  developed  handling  strength.  It  is  not  necessary  to clamp the parts unless

movement during cure is likely.

Cure:

Complete cure is obtained after three days at room temperature. After 24 hours, approximately 90% of

full cure properties are attained.

Clean Up:

It  is  important  to  remove  excess  adhesive  from  the  work  area  and  application equipment before it

hardens. Many common solvents  are suitable for removing uncured adhesive. Consult with your supplier's

information pertaining to the safe and proper use of solvents.

Packaging:

50 ml and 200 ml Conjoined double tube

GENERAL INFORMATION:

This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be

selected  as  a  sealant for chlorine or other strong oxidizing materials.

For safe handling information on this product,consult the Material Safety Data Sheet,(MSDS).

Storage:

Store product in unopened container in a cool dry location. Ideal conditions are within the range 8 to 21

degrees C  (46  to  70  degrees  F )  and  are  recommended  for  long  term  storage.  Exposure  to  higher

temperatures (greater than 28 degrees C) for prolonged periods should  be avoided  as extended  exposure

to warm conditions can adversely affect product properties. For further specific shelf life information,contact

your local Technical Service Center.

Note:

The data contained herein are furnished for information only and are believed to be reliable.We cannot

assume responsibility for the results obtained by others over whose methods we have no control. It is the

user's responsibility to determine suitability for the user's purpose of any production  methods  mentioned

herein and to adopt such precautions as may be advisable for the protection of  property  and of  persons

against any hazards that may be involved in the handling  and  use  thereof.  In  light  of  the  foregoing,

TIEAKO^® specifically disclaims all warranties expressed or implied, including warranties of

merchantability or  fitness  for  a particular  purpose, arising from sale or use of TIEAKO^®

products. TIEAKO^® specifically disclaims  any  liability  for  consequential  or  incidental

damages  of  any  kind, including lost profits. We recommend that each prospective user test his

proposed application before repetitive use, using this data as a guide.